PIICEON, INC. DISPATCHER 805-1400 Card Type Modem (asynchronous) Chipset Rockwell Maximum Data Rate 14.4Kbps Maximum Fax Rate 14.4Kbps Data Bus Compaq communications bus Fax Class Class I & II Data Modulation Bell 103A/212A ITU-T V.21, V.22, V.23, V.22bis, V.32, V.32bis Fax Modulation ITU-T V.17, V.21CH2, V.27ter, V.29 Error Correction/Compression MNP5, MNP10, V.42, V.42bis [Image] CONNECTIONS Function Label Function Label Line out CN1 Compaq communications bus CN3 Line in CN2 SUPPORTED STANDARD COMMANDS Basic AT Commands +++, ‘comma’, A/ A, B, C, E, H, L, M, N, O, Q, V, W, X, Y, Z &C, &D, &F, &G, &K, &L, &M, &P, &Q, &R, &S, &T, &V, &W, &Y, &Z Extended AT Commands \A, \B, \G, \J, \L, \W %C, %E, %F, %L S-Registers S0, S1, S2, S3, S4, S5, S6, S7, S8, S9, S10, S12, S14, S16, S18, S21, S22, S23, S24, S25, S27, S28, S29, S30, S31, S32, S33, S36, S38, S39, S40, S41, S46, S48, S82, S86, S91, S92, S95, S201 Special AT Commands -K, -Q, *H, )M, @M, :E, #CID Note: See MHI help file for full command documentation. Proprietary AT Command Set BREAK TYPE Type: Configuration Format: AT [cmds] \Kn [cmds] Description: Configures action of break signal Command Function \K0 Online command mode enabled, do not send break to remote modem. \K1 Break sent to remote modem and buffered cleared. \K2 Online command mode enabled, do not send break to remote modem. \K3 Send break to remote modem immediately. \K4 Online command mode enabled, do not send break to remote modem. \K5 Send break with transmitted data. CALLBACK Type: Configuration Format: AT [cmds] *Pn:xxxx:<#> Description: Stores the information for callback number n. When enabled, the modem will call back the phone number indicated and request the matching password. CELLULAR DRIVER DOWNLOAD Type: Immediate Format: AT [cmds] ^C2 Description: Initiates an ASCII transfer of a new cellular phone driver. CELLULAR DRIVER INFORMATION Type: Immediate Format: AT [cmds] ^I [cmds] Description: Displays information about the currently loaded cellular phone driver. CELLULAR PHONE STATUS Type: Immediate Format: AT [cmds] ^T6 [cmds] Description: Displays the current status of the connected cellular phone. Bit Value Function 0 0 Cellular phone is not receiving an incoming call. 1 Cellular phone is receiving an incoming call. 1 0 Cellular phone is not in use. 1 Cellular phone is in use. 2 0 Cellular phone is not locked. 1 Cellular phone is locked. 3 0 Cellular service present. 1 Cellular service not present. 4 0 Cellular phone is off. 1 Cellular phone is on. 5 0 Cellular driver is not initialized. 1 Cellular driver is initialized. 6 0 Not used. 7 0 Cellular cable not detected. 1 Cellular cable detected. CONNECT MODE Type: Configuration Format: AT [cmds] \Nn [cmds] Description: Controls the type of connection the modem will connect with. Command Function \N0 Modem will connect in normal mode. \N1 Modem will connect in normal mode. \N2 Modem will attempt V.42bis mode, then MNP mode, then hang up. \N3 Modem will attempt V.42bis mode, then MNP mode, then normal mode. \N4 Modem will attempt V.42bis mode, then hang up. \N5 Modem will attempt MNP mode, then hang up. DCE LINE SPEED Type: Register Format AT [cmds] S37=n [cmds] Description: Sets the maximum allowable data exchange rate attempted during handshake process. Command Function S37=0 Speed of last connection. S37=1 Maximum speed set to 300bps. S37=2 Maximum speed set to 300bps. S37=3 Maximum speed set to 300bps. S37=5 Maximum speed set to 1200bps. S37=6 Maximum speed set to 2400bps. S37=7 Maximum speed set to 1200/75bps. S37=8 Maximum speed set to 4800bps. S37=9 Maximum speed set to 9600bps. S37=10 Maximum speed set to 12Kbps. S37=11 Maximum speed set to 14.4Kbps. S37=12 Maximum speed set to 7200bps. DIAL Type: Immediate Format: AT [cmds] D<#> [cmds] Description: Dials telephone number according to any modifiers included in the string. Note: Any combination of modifiers can be used to produce the desired dial functions in sequence. Command Function DJ MNP10 link will be negotiated at 1200bps for this call. DK MNP10 power level adjustment enabled for this call. DL Re-dial last number. DP Dial following digits in pulse mode. DS=n Dial stored telephone number n. DT Dial following digits in tone mode. DW Dialing resumed following dial tone detection. D, Dialing paused for amount of time specified in S8 register. D"WXY" Optional method of denoting telephone numbers. Letters enclosed in quotes are interpreted as numbers according to the system found on a telephone keypad. D! Flash function initiated. Modem commanded to go off-hook for specified time before returning on-hook. D@ Wait for Quiet Answer function enabled. Modem waits until a "quiet answer," a ring-back signal followed by silence up to the time specified in S7, is received prior to executing the rest of the dial string. DIAL (CON’T) D& Wait for AT&T credit card ("bong") tone detection function enabled. Waits for bong tone for amount of time specified by the S7 command. D$ Wait for prompt tone detection function enabled. Waits for prompt tone for amount of time specified by the S7 command. D^ Toggles calling tone on or off for this call. D> Sends grounding pulse on EARTH relay line. D; Modem returned to idle state after dialing. The semicolon can only be placed at the end of the dial command. DISPLAY STORED NUMBERS Type: Immediate Format: AT [cmds] \F [cmds] Description: Displays all stored numbers. PROTOCOL/SPEED Type: Configuration Format: AT [cmds] Fn [cmds] Description: Selects the protocol and speed the modem will attempt to connect at. Command Function F0 Auto-detect the highest common connect speed. F1 Select V.21 or Bell 103 at 300bps speed. F3 Select V.23 at 75/1200bps speed. F4 Select V.22 at 1200bps speed. F5 Select V.22bis at 2400bps speed. F6 Select V.32/V.32bis at 4800bps speed. F7 Select V.32bis at 7200bps speed. F8 Select V.32bis/V.32 at 9600bps speed. F9 Select V.32bis at 12Kbps speed. F10 Select V.32bis at 14.4Kbps speed REMOTE CONFIGURATION END Type: Configuration Format: AT [cmds] *E [cmds] Description: Ends the current remote configuration session. REMOTE CONFIGURATION PASSWORD Type: Configuration Format: AT [cmds] *Cxxxx [cmds] Description: Stores the password that must be sent by a remote modem to enter a remote configuration session on the local modem. REMOTE CONFIGURATION REQUEST Type: Configuration Format: AT [cmds] *Rn [cmds] Description: Requests the remote modem to start a remote configuration session. REPORT INFORMATION Type: Immediate Format: AT [cmds] In [cmds] Description: Displays information requested. Command Function I0 Reports modem model and speed. I1 Reports ROM checksum. I2 Tests and reports ROM checksum. I3 Reports firmware revision. I4 Reports OEM identifer. I5 Reports country code.